SPECIALIST DEALER
SEARCH

Find your
WAREMA specialist dealer

Special components

Features

  • Device for the simultaneous operation of multiple 230 V AC sun shading drives
  • Ideal for application cases in which motor lines have been forgotten
  • The motor current of all drives is guided with the push button or with the motor control unit or actuator
  • Terminals for line loop-through in order to build and simultaneously control large drive groups
  • Dead man operating mode executes move command as long as the switch is actuated
  • Compact design enables installation in flush-mounted junction box
  • Surface-mounted model for 2 motors with preassembled connecting lines STAK/STAS 3

Product

ProductArticle number
Parallel control unit UP1002418
Parallel control unit, AP1002420

Technical data

Operating voltage230 V AC
Output2 x 230 V AC, 700 VA
Logic behaviourDead man
Degree of protectionIP 20 (UP)
IP 54 (AP)
Safety classII
InstallationSurface-mounted (AP)
Flush-mounted (UP)
Dimensions48 x 48 x 23.5 mm (UP)
88 x 88 x 47 mm (AP)
Line length: connecting line 25 cm
Cable exit 40 cm each

     

Features

  • Device for the simultaneous operation of multiple 230 V AC sun shading drives
  • Contact multiplication, allowing simultaneous control of two or more sun shading drives using a single operating element or the output of a single motor control unit
  • The cutoff relay and the motors are supplied with 230 V from an additional 5th wire
  • Terminals for line loop-through in order to build and simultaneously control large drive groups
  • Dead man operating mode executes move command as long as the switch is actuated
  • Compact design enables installation in flush-mounted junction box

Product

ProductArticle number
Cutoff relay UP1002417

Technical data

Operating voltage230 V AC
Output2 x 230 V AC, 700 VA
Logic behaviourDead man
Degree of protectionIP 20
Safety classII
InstallationFlush-mounted
Dimensions48 x 48 x 23.5 mm

     

Features

  • Device for potential isolation and building groups
  • Potential isolation for long control lines
  • Builds additional groups in control line systems
  • Downstream motor control units can still be operated via local push buttons or via a central control unit
  • In time mode, the MSE enters lock mode after the push button is pressed for approx. 2 seconds. Operating the push button for a shorter duration generates a tilting impulse (on slat products)
  • Device is supplied with 24 V DC SELV via a control line system
  • Compact design enables installation in flush-mounted junction box

Product

ProductArticle number
Uniswitch ZL UP1002473

Technical data

Operating voltage24 V DC
Control voltage24 V DC
Outputfloating, 72 W
Logic behaviourTime mode
Degree of protectionIP 20
Safety classIII
InstallationFlush-mounted (UP)
Dimensions48.5 x 48.5 x 20.4 mm

     
Features

Features

  • SMI distribution board for up to 12 motors with 2 separate supplies
  • SMI distributor for parallel switching of up to 12 SMI motors
  • Fuse protection using miniature fuse per 6 motor clamps
  • Connection terminals for secure installation

Product & accessories

ProductArticle number
SMI distributor, AP
2011711
SMI distribution board, REG
2011710
Accessories
Article number
Strain relief kit for AP housing
1002236

Technical data

Operating voltage
230 V AC
Degree of protection
IP 30 (AP)
Safety class
I
Installation

Surface-mounted (AP)
DIN rail-mounted (REG)
Dimensions
210 x 80 x 60 mm (AP)
12 MW (REG)

     

Find a qualified
advisor in your area now

  • Individual consultations
  • Comprehensive product selection
  • Inspirations for your project